goodguys75 Posted November 15, 2011 Posted November 15, 2011 having a hell of a time getting the carb to run correctly...all re-built...should i just get and aftermarket????? Want to stay all factory, but 125.00 for a factory oem is a lot of money for that...thanks for any input......andre Quote
mineurbiz Posted November 15, 2011 Posted November 15, 2011 (edited) Replaced both pilot and main jets? I have to spray the heck out of mine the first time I went to clean it, probably took 3 cleanings, spraying every little hole and crack out!! I also had air leaks, I pulled the intake manifold off and had to replace the gasket and some have seen splits in the intake boot. Edited November 15, 2011 by mineurbiz Quote
goodguys75 Posted November 16, 2011 Author Posted November 16, 2011 all is clean and new..........whatever could be replaced was.... Quote
mineurbiz Posted November 16, 2011 Posted November 16, 2011 If you haven't already, I would check the jets again, so much old gunk in those carbs, they might become clogged or check for air leaks. Are you still using the stock air filter also? Quote
Jakster884 Posted November 16, 2011 Posted November 16, 2011 I bought a new carb $28.00 from:http://dratv.stores.yahoo.net/ DRATV. It was from Japan so it should be a good one no China crap. Finally put it on and no more leaking bowl. Quote
BLUE STEEL Posted November 17, 2011 Posted November 17, 2011 I bought a new carb $28.00 from:http://dratv.stores.yahoo.net/ DRATV. It was from Japan so it should be a good one no China crap. Finally put it on and no more leaking bowl. Was that the 20MM one you bought? Quote
Jakster884 Posted November 17, 2011 Posted November 17, 2011 Was that the 20MM one you bought? Yes it was. It was not the stock but for the 88Kit I have. I was supprised it came from Japan. I noticed the Stock carb is $50.00 or even $125.00 Quote
BLUE STEEL Posted November 17, 2011 Posted November 17, 2011 Yes it was. It was not the stock but for the 88Kit I have. I was supprised it came from Japan. I noticed the Stock carb is $50.00 or even $125.00 Will the 20 mm carb work with the stock motor? Quote
Jakster884 Posted November 18, 2011 Posted November 18, 2011 Will the 20 mm carb work with the stock motor? This I am not sure of. I would give them a call to see if it will. Hopefully someone on the board can chime in. Help a brotha out please. Quote
dunefreak Posted November 18, 2011 Posted November 18, 2011 I want to say a 20mm is a bit too big for stock. You can just measure the original one and see if DRATV sells one that size. Quote
JVZ Posted December 13, 2011 Posted December 13, 2011 I put a 20mm on my stock motor with a cobra exhaust and it runs good. I had to mess with it awhile and tune it get it running good, but it runs well for a stock motor. Quote
dunefreak Posted December 13, 2011 Posted December 13, 2011 I put a 20mm on my stock motor with a cobra exhaust and it runs good. I had to mess with it awhile and tune it get it running good, but it runs well for a stock motor. Jason, yours might have a big bore 88 kit in it. Quote
EY3BA11 Posted December 15, 2011 Posted December 15, 2011 Stock carb is 16mm im sure you could put a 20mm on it and just have to jet the crap out of it to get it to run right. dratv shows they have the 16mm's in stock for 50 bucks. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.